Kukko Mobile inductive bearing heater

Kukko Magnet probe

Kukko Workshop inductive bearing heater

Kukko Magnet probe

Kukko Protective blankets for pulling jobs

Kukko Protective blankets for pulling jobs

Kukko Universal press frame for silent bushings DescriptionSeries is built on a modular system.Easy-to-replace individual components that can be combined in a number of different ways.Grease hydraulics.Hydraulic spindle.Milled thread treated with special coating. UseFor replacing bearings on front and rear axles without dismantling the axle, e.g. silent bearings, hydraulic supports, plastic bearings, supporting joints, absorber rubber. AdvantagePressure pad sets available for a variety of vehicle types.Little force required for a strong pulling performance.Piston functions on the axis and does not turn in the hydraulic spindle.Spindle extensions enable the unit to be adjusted quickly to a range of different requirements.Spindle head band prevents the wrench from slipping off.Almost all components available as replacement parts, time-saving order process thanks to numbering system. How it worksScrew the upper spindle together before use.Insert the pressure piece onto the pressure bolt.Screw the hydraulic spindle into the press frame from above.Insert a suitable pressure pad.Position the press frame over the axle.Operating the upper spindle builds up pressure. Safety informationThe press frame´s support surfaces must always be straight and sit fully beneath the part to be removed.Do not use any electrical or pneumatic servo screwdrivers or hammer drills.Protective blanket required.Protective goggles required.

Kukko Universal press frame for silent bushings DescriptionSeries is built on a modular system.Easy-to-replace individual components that can be combined in a number of different ways.Grease hydraulics.Hydraulic spindle.Milled thread treated with special coating. UseFor replacing bearings on front and rear axles without dismantling the axle, e.g. silent bearings, hydraulic supports, plastic bearings, supporting joints, absorber rubber. AdvantagePressure pad sets available for a variety of vehicle types.Little force required for a strong pulling performance.Piston functions on the axis and does not turn in the hydraulic spindle.Spindle extensions enable the unit to be adjusted quickly to a range of different requirements.Spindle head band prevents the wrench from slipping off.Almost all components available as replacement parts, time-saving order process thanks to numbering system. How it worksScrew the upper spindle together before use.Insert the pressure piece onto the pressure bolt.Screw the hydraulic spindle into the press frame from above.Insert a suitable pressure pad.Position the press frame over the axle.Operating the upper spindle builds up pressure. Safety informationThe press frame´s support surfaces must always be straight and sit fully beneath the part to be removed.Do not use any electrical or pneumatic servo screwdrivers or hammer drills.Protective blanket required.Protective goggles required.

Kukko Universal wiper arm puller

Kukko Universal wiper arm puller

Kukko Universal wiper arm puller set DescriptionThe one-piece bell-shaped design fits on all VW, Audi, Seat, Skoda and other models.Shaped for optimal fit with all commonly used types of wiper arms.Mechanical pressure screw.Milled thread treated with special coating.Instructions on the cover.Secure storage in special foam. UseGeneral purpose set used for pulling tight-fitting, rusted and deep-set windscreen whiper arms. AdvantageWindshield wiper arms can be pulled without removing the bonnet.The threaded spindles are guided by a movable bush, which allow the puller to be fitted to the edge of the arm at the start and in the middle at the end of the removal process.Suitable for front and rear wipers with the washing fluid hose passing through the hub.Special threads enable especially high pulling forces.Solid, single-piece milled body for high strength.No damage to wiper arm, shaft, etc.No paint scratching.No glass damage How it works128-F-SW general-purpose wiper arm puller1. After removing the detachable cap, unscrew the stop nut to a point just before reaching the end, then attach and fix the gripper behind the wiper arm.2. The gripper´s counter hold is provided by the spanner flat (SW 15 mm).3. Remove the wiper arm by tightening pressure spindle.4. The supplied brass pressure piece is used for wiper arms with integrated windscreen washer jetsGeneral-purpose puller with self-centering extractor hooks.1. The part due to be removed (e.g. a gear or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.2. With increasing spindle pressure, the pulling hooks clasp the part to be removed with an increasing amount of force.3. The puller must be positioned centrally for centre shafts. Safety informationDo not use any electrical or pneumatic servo screwdrivers or hammer drills.Protective blanket required.Protective goggles required.

Kukko Universal wiper arm puller set DescriptionThe one-piece bell-shaped design fits on all VW, Audi, Seat, Skoda and other models.Shaped for optimal fit with all commonly used types of wiper arms.Mechanical pressure screw.Milled thread treated with special coating.Instructions on the cover.Secure storage in special foam. UseGeneral purpose set used for pulling tight-fitting, rusted and deep-set windscreen whiper arms. AdvantageWindshield wiper arms can be pulled without removing the bonnet.The threaded spindles are guided by a movable bush, which allow the puller to be fitted to the edge of the arm at the start and in the middle at the end of the removal process.Suitable for front and rear wipers with the washing fluid hose passing through the hub.Special threads enable especially high pulling forces.Solid, single-piece milled body for high strength.No damage to wiper arm, shaft, etc.No paint scratching.No glass damage How it works128-F-SW general-purpose wiper arm puller1. After removing the detachable cap, unscrew the stop nut to a point just before reaching the end, then attach and fix the gripper behind the wiper arm.2. The gripper´s counter hold is provided by the spanner flat (SW 15 mm).3. Remove the wiper arm by tightening pressure spindle.4. The supplied brass pressure piece is used for wiper arms with integrated windscreen washer jetsGeneral-purpose puller with self-centering extractor hooks.1. The part due to be removed (e.g. a gear or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.2. With increasing spindle pressure, the pulling hooks clasp the part to be removed with an increasing amount of force.3. The puller must be positioned centrally for centre shafts. Safety informationDo not use any electrical or pneumatic servo screwdrivers or hammer drills.Protective blanket required.Protective goggles required.

Kukko female adapter M10 / M10

Kukko female adapter

Kukko female adapter M12 / M10

Kukko female adapter M12 / 15x16G

Kukko female adapter M12 / M7

Kukko female adapter M14x1,5 / M14x1,5

Kukko female adapter M18x1,5 / M18x1,5

Kukko female adapter

Kukko female adapter

Kukko female adapter

Kukko Workshop tool trolley DescriptionTilt-resistant with stable design.Smooth and stable load castors, including two with brakes.Simple loading of extracts with KUKKO-L-Boxx cases.Fully assembled prior to delivery, including black rubber mat in the storage compartment. UseWorkshop tool trolley that can be combined with drawers for the proven KUKKO L-BOXX system. AdvantageIdeal work height for use in workshops and industry.Smooth-running extracts and self-closing mechanism for the drawers.KUKKO L-BOXX - quickly and easily adjustable with quick locking mechanism.Simply remove the drawers to use the large L+BOXX separately.

Kukko Wall panel, blank